Datsun 541016-2L Front
240Z, 260Z, 280Z (’70-’78)
( Pair )
Top Strut Mounts
Camber & Caster adj.
(Stage 2- Street/ Race)

• Description

  Product Description

  Further Product Info / Sales :
  Ph 1888 847 9099 Int. + 61 2 9556 1799 (24/7)

  Further Product Info / Sales :
  Ph 1888 847 9099 (24/7)
  Int. + 61 2 9556 1799 (24/7)

  When 2nd Best isn’t Enough ….

  KMAC Datsun 240z 260z 280z (1970 – 1978)
  FRONT CAMBER (AND CASTER) “REPLACEMENT” STRUT TOPS ( Pair )
  (Stege 2- Street/ Race). # 541016- 2L . Provides extra Neg. Camber, Pos. Caster .

  ( Also Rear Camber tops # 541026 – K ) . Provides extra Pos. Camber

  WITH KMAC THERE ARE NO MODS (cutting top of strut towers, drilling or need to remove one of the 3 OEM securing bolts)

  KMAC – Simply replaces the OEM Top Strut Mounts – All from coil spring up. Now OEM diam, coil seats indeted plus seat to fit all popular coil overs 60″ to 70″ I.D. )

  WHAT YOU WOULD EXPECT – KMAC “EXPERIENCE” OF MANUFACTURING OF FRONT & REAR ADJUSTER KITS LONGER THAN ANY OTHER BRAND.

  ADDITIONAL KMAC FEATURES :
  Precisely adjust from engine bay (no strut removal)
  Separate Caster settings and no height increase.
  Extra H/Duty Self Align Spherical bearings.(Teflon lined)
  Separate (massive) 85mm (3 3/8″) diameter fully sealed thrust bearings
  For steering loads – prevent spring drag / binding.

  

  ANOTHER KMAC UPDATE INCORPORATED INTO THE DESIGN : With KMAC we do not rely just on the “single spherical ball” instead separate radial thrust bearings are included to take the “Steering Loads” (which also resolves annoying spring drag/ noise/ binding). Massive 85mm (3 3/8″) diameter fully sealed bearings (again by far biggest in the industry)

  Genuine KMAC STRUT TOPS – UNLIKE OTHER BRANDS NOT STEEL OR SOFT BILLET ALLOY : But the very highest 7075 aircraft grade aluminum with “Extra H/Duty” self align spherical bearings (self lubed – PTFE lined) then encased in elastomer to extend life / day to day commuting (centers are also “replaceable” for virtual lifetime usage) and designed for minimum stack height.

  NOTE : SUPERSEDES THE CURRENT INDUSTRY STANDARD WHICH HAS BEEN AROUND FOR YEARS – ‘SLOT’ adjustment. Unlike KMAC are only available in a solid / uncompromising STAGE 3 Full Race version (steel sphercial bearings mounted on a non shock absorbing steel plate).
  THIS SLOT DESIGN, BESIDES PROVIDING LESS ADJUSTMENT because of the need for access to the hold down bolts, is also time-consuming to adjust and on many vehicles requires removal of the strut.
  Note : Most brands the “single” spherical ball is also taking the steering loads.
  Unlike KMAC where all Stage 2 (Street/ Race) and Stage 3 (Full Race) incorporate purposely designed vertical thrust bearings ( these are fully sealed and massive 85 mm diameter). Reducing steering effort and preventing annoying noise through spring drag / binding．

  ON TRACK DAYS : ABILITY TO DIAL IN “EXTRA NEGATIVE CAMBER” TO SIGNIFICANTLY REDUCE UNDERSTEER, in the pursuit of hitting these corner apexes every time and allowing to go deeper into the corners with increased traction and braking response. With the result of further lowering lap times in the quest for front row of the grid on race days ! (also see below front lower control arm adjusters for extra adjustment.)

  RESULT : Finally – The adjustment capability TO CHANGE TIRE “CONTACT ANGLES” to correctly resolve costly premature edge tire wear and steering pull. The result of other than showroom height conditions – day to day commuting, encountering high cambered roads, altered height through load carrying or lowering, fitting wide profile tires/wheels and curb knock damage. Along with the ability to improve traction understeer/oversteer.

  *ALSO ● ● ● ● SEE COMPLETE RANGE OF “FRONT AND REAR BUSHINGS ” 1st. ITEM TO FAIL. ALL THE VERY LATEST DESIGN BREAKTHROUGHS (Experience of manufacturing performance bushings longer than anyone else – 1964). Resolving costly, premature bush wear with resultant wheel tramp, vibration, loss of traction under brake and acceleration.

  CHECK LIST / EXTRA FEATURES KMAC BUSHES VERSES OTHER BRANDS: Where other brands merely replace “OEM rubber bushes with urethane “ to eliminate the OEM oil and air voids in the endeavour to improve brake and steering response. The problem here is that with today’s autos multi link arms and different mount angles, this inhibits the suspension arms traveling through their required arcs which can cause even more wheel tramp / loss of traction with arms binding, locking up and lead to breakage!

  KMAC bushings therefore where required are “Mono ball / 2 axis / self aligning ” with the unique design providing more than two and a half times for both the load bearing area and shock absorption over of OEM bushes.

  This KMAC design breakthrough also finally resolving once and for all the issue with “steel spherical bearings“. Their wafer thin teflon style liners used soon pounding out with resultant metal to metal contact, noise.

  Also because of ever increasing speed of assembly lines all today’s Autos now only have Front and Rear Toe “directional adjustment”. “NEW CAR INDUSTRIES BEST KEEP SECRET”, KMAC FRONT & REAR KITS ALLOW TO CHANGE TIRE CONTACT ANGLES – ESSENTIAL TO RESOLVE COSTLY, PERMATURE EDGE TIRE WEAR / CORRECTLY RESOVE STEERING PULL.

  THE ACTUAL KMAC “PATENTED DESIGN BUSH ADJUSTMENT SYSTEM” HAS REVOLUTIONIZED THE INDUSTRY – PRIOR TO THIS – THE LAST 40 OR SO YEARS HAS REQUIRED THE NEED FOR LABOUR INTENSIVE DISASSEMBLY AND BUSH REMOVAL. THEN THE INACCURATE TRIAL AND ERROR NEED FOR BUSH REPOSITIONING EACH TIME TO CHANGE ALIGNMENT SETTINGS. INSTEAD NOW WITH K-MAC WE HAVE CHANGED ALL THAT – IT IS PRECISE SINGLE WRENCH ADJUSTMENT ACCURATELY ON CAR (UNDER LOAD) DIRECT ON ALIGNMENT RACK. THEN SECURED BY THE K-MAC UNIQUE “POSITIVE LOCK” SYSTEM.